Login  |  Register
Nissanhelp.com - All About Nissan
Do-It-Yourself Maintenance Owners Manuals Recalls/Campaigns Service Bulletins Service Manuals Nissan OBDII Codes Glossary & Acronyms More...
Member's Ride Photos Stock Photo Gallery
Classifieds - For Sale Classifieds - Wanted To Buy Classifieds - Mechanic Wanted Classifieds - Auto Services Search Auto Parts
Register FAQ Social Groups Mark Forums Read
2007 Maxima - No acceleration Forums > > 2007 Maxima - No acceleration 2007 Maxima - No acceleration
Forgot Password? Join Us!

Maxima Nissan Maxima Discussion Forum

Thread Tools Display Modes
Old 02-02-2018, 09:50 AM
lordhao lordhao is offline
Registered User
2007 Maxima
2012 Murano
Join Date: Feb 2018
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default 2007 Maxima - No acceleration

Having some issue with my Maxima. Around this time last year, my maxima was experiencing loss of acceleration once I go pass 30mph. Basically all the car does when I press the gas paddle and nothing would happen. There are no dashboard lights to tell me something is not working or needed to be checked. After some research, it was deducted to the ABS sensors since the car drives fine if I disconnect any of the rear wheel sensors. I ended up fixing the issue by changing both rear sensors, and the passenger wheel hub.

Unfortunately, after 3-4 months after the fix, the car is exhibiting the same issue again. I thought it might be the rear hub on the driver side has gone bad since I've change that side yet. But after installing a new rear wheel hub, the same problem still persist.

Any suggestion on what I should do next? front sensors? front wheel hubs? or is it something else entirely?

I'm currently driving the car with one of the rear sensors unplug. So the ABS and Anti Traction warning lights are showing on my dashboard. I needed to keep one of the rear sensor connected for the speedometer to work, but other than that the cars drives fine.

Any suggestions is welcome. Thank you in advance.
Reply With Quote
Old 06-12-2018, 05:52 PM
OilCanObserver OilCanObserver is offline
1995 Maxima
Join Date: Apr 2010
Posts: 57
Thanks: 3
Thanked 5 Times in 5 Posts

1. did you test the sensor, using ohmmeter? make sure you have the correct range of ohms for your vehicle's sensor. (in the video: 1.5 to 1.7 Kohms- yours could be different) if out range suspect the sensor is defective.
if reading is too high (infinite) suspect bad sensor or intermittent/broken wire or connector. try to test the known to be good sensor for comparison.

2. test for the integrity of the wires, there could be a break or loose connector. sorry i'm not familiar with the configuration of your system. if there's a connector near the sensor, unplug the sensor, put a short (use a jumper), use your ohmmeter near the control module, there should be a low ohm reading if no break, slightly higher reading for the rear than the front (longer wires) & depending on the accuracy of the ohmmeter. good luck & post whatever you might have done to correct the problem
Reply With Quote
Old 06-16-2018, 08:01 AM
mpe235's Avatar
mpe235 mpe235 is offline
2015 Rogue
Join Date: Jun 2006
Location: New York
Posts: 5,528
Thanks: 5
Thanked 258 Times in 239 Posts

Remove the white plastic cover behind both rear wheel bearings. Cut the top portion so it looks like a U and reinstall them.
Reply With Quote
Old 05-17-2019, 11:07 AM
lordhao lordhao is offline
Registered User
2007 Maxima
2012 Murano
Join Date: Feb 2018
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts

@OilCanObserver - I tried to use the omh meter to test, but based on what I read online, my sensor can't be test that way and require some special tool to perform the test.
However I was able to get a hand on a Launch Code scanner and did confirm that the Rear Right sensor was not registering. However, after replacing that sensor with a new one, all the dashboard lights does away, but my acceleration issues persisted. On top of that, if I break at low speed (20-25mph) I feel my ABS is activating. Some research online is saying that it might be then ABS Actuator? any idea how to test that?

@Mpe235 - what does cutting the top portion of the U shape in the plastic cover do? how would it help with the issue?

Reply With Quote
Old Yesterday, 12:50 AM
smj999smj's Avatar
smj999smj smj999smj is offline
Master Enthusiast
2006 Pathfinder
2003 Frontier King Cab
2003 Frontier KC SVE 4x4
Join Date: Jun 2012
Location: Prospect, VA
Posts: 1,707
Thanks: 1
Thanked 246 Times in 229 Posts

Refer Nissan technical service bulletin # NTB07-016b:

Reply With Quote


2007, acceleration, maxima

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -8. The time now is 03:20 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO v2.0.42 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.