Login  |  Register
Nissanhelp.com - All About Nissan
Do-It-Yourself Maintenance Owners Manuals Recalls/Campaigns Service Bulletins Service Manuals Nissan OBDII Codes Glossary & Acronyms More...
Member's Ride Photos Stock Photo Gallery
Classifieds - For Sale Classifieds - Wanted To Buy Classifieds - Mechanic Wanted Classifieds - Auto Services Search Auto Parts
Register FAQ Social Groups Mark Forums Read
Forums > > > 2006 Frontier
Forgot Password? Join Us!


2.3.0

2006 Frontier
2006 Nissan Frontier Service Bulletins
New entries announced in forum Latest Uploads
Allowances: 0 files/0 used

Keyword Filter
Sort by

  Entries Show full/short entries
Access denied NTB17-082a
-REVISED-
VARIOUS NISSAN MODELS; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING
The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK)
AND
  • DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097).
  • An EVAP leak has been detected where the vent control valve mounts to the canister.
  • The vent control valve O-ring seal is determined to be the cause.

Discussion Thread
 
Send to Friend Suggest other entries I might like
08-21-2017
1.71 Mbytes Hits 109
Keywords: control dtc p0456 valve vent
Access denied NTB17-030
VARIOUS NISSAN MODELS; FUEL TANK IS SLOW OR DIFFICULT TO FILL
The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full).

Discussion Thread
 
Send to Friend Suggest other entries I might like
03-20-2017
640.54 Kbytes Hits 271
Keywords: difficult fill fuel tank slow
Access denied NTB17-026
VARIOUS NISSAN MODELS; BALL JOINT AXIAL END PLAY PROCEDURE
When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM).

Discussion Thread
 
Send to Friend Suggest other entries I might like
03-07-2017
743.03 Kbytes Hits 77
Keywords: play end axial joint all
Access denied NTB15-079a
-REVISED-
2005-2015 NISSAN FRONTIER; MIL ON WITH DTC P0448
The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM.

Discussion Thread
 
Send to Friend Suggest other entries I might like
02-19-2016
58.72 Kbytes Hits 38
Keywords: close miil valve evap control canister vent p0448 dtc
Access denied NTB16-003
VARIOUS NISSAN MODELS; NISSAN INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES
The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years.

Discussion Thread
 
Send to Friend Suggest other entries I might like
01-05-2016
157.39 Kbytes Hits 145
Keywords: key intelligent
Access denied NTB15-107
2005-2008 NISSAN PATHFINDER, FRONTIER, XTERRA WITH V6 ENGINE; SERVICE INFORMATION FOR REMANUFACTURED A/T FROM ATC DRIVETRAIN
A remanufactured automatic transmission supplied by ATC Drivetrain is installed in an APPLIED VEHICLE
AND
CONSULT-III plus (C-III plus) is not able to communicate with the TCM through Diagnosis (One System)
OR
C-III plus is able to communicate with the TCM, but the TCM part number’s (P/N) sixth digit is a “5”, “6”, or “7” (for example, 31020-7xxxx).

Discussion Thread
 
Send to Friend Suggest other entries I might like
11-30-2015
307.49 Kbytes Hits 16
Keywords: a/t remanufactured drivetrain
Access denied NTB15-060
VARIOUS NISSAN; SERVICING RUN FLAT TIRES AND LOW PROFILE TIRES EQUIPPED WITH TPMS SENSORS
When servicing run flat tires or low profile tires:
  • Special equipment and procedures are required to avoid damage.
  • Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires.
  • TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
  • To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires.

Discussion Thread
 
Send to Friend Suggest other entries I might like
07-06-2015
1.58 Mbytes Hits 77
Keywords: tires tpms run-flat low-profile
Access denied NTB15-055
2005-2015 ALL NISSAN MODELS; ECM REPROGRAMMING – SERVICE INFORMATION
After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming.

Discussion Thread
 
Send to Friend Suggest other entries I might like
06-24-2015
43.15 Kbytes Hits 157
Keywords: ecm reprogramming
Access denied NTB15-010b
-REVISED-
2005-2008 NISSAN PATHFINDER, FRONTIER, XTERRA WITH V6 ENGINE; SPECIAL INSTRUCTIONS FOR INSTALLING REMANUFACTURED A/T FROM ATC DRIVETRAIN
The automatic transmission needs to be replaced, for any reason, in an applied vehicle

Discussion Thread
 
Send to Friend Suggest other entries I might like
06-17-2015
39.59 Kbytes Hits 26
Keywords: transmission automatic
Access denied NTB15-043
VARIOUS NISSAN MODLES; PRECAUTIONS FOR CLEANING PAINTED ALLOY WHEELS
The appearance of painted alloy wheels can be damaged if acidic cleaners are used.

Discussion Thread
 
Send to Friend Suggest other entries I might like
05-07-2015
327.36 Kbytes Hits 81
Keywords: alloy wheels cleaning painted
 


 
CarZone Auto | Nissan and Infiniti Service Center

 

All times are GMT -8. The time now is 06:07 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO v2.0.42 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.